Home About Us Products Contact Us
 
PRODUCTS
 
DIN 3015 - PART -1
TUBE CLAMPS LIGHT SERIES Download catalog
The standard series Pipe clamps are designed according to DIN 3015 - Part - 1 available in Plastic, Aluminium clamp bodies with Steel / S. S. plates & bolts standard series Pipe - tube clamps are normally used for general Purpose applications & the W.P. range up to 1500 PSI (100 BAR) in the Steel / stainless steel Piping System. Standard series pipe - tube clapms are available along with Multilayer, welding plates, rail nuts, construction types, rubber inley types & many more.
   
   
   
DIN 3015 - PART - 2
TUBE CLAMPS HEAVY SERIES Download catalog

Heavy series Pipe clamps are designed according to DIN 3015 - Part - 2 available in Plastic, Aluminium clamp bodies with Steel / S.S. plates & bolts

Heavy series Pipe - Tube clamps are normally used for general Purpose applications & the W.P. range more then 1500 PSI (100 BAR) and up to 8000 psi (600 BAR) in the Steel / stainless steel Piping System.

Heavy series pipe - tube clamps are available along with Multilayer, welding plates, rail nuts, construction types, rubber inley types & many more.

   
   
   
DIN 3015 - PART -3
TUBE CLAMPS TWIN SERIES Download catalog

Twin Series clamps are designed to clamp two indentical Pipe - tube to the Piping Systems. Twin series clamps are available in Sizes from 6 MM od up to 42 MM od. Twin Series clamps are capable to resist W.P. up to 1500psi (100 Bar) in the Piping Systems.

Twin Series clamps are designed with thick plates & heavy bolts to resist High Pressure Piping Application Twin Series clamps are available in Plastic - PP / PA (6) with Steel & stainless steel Plates & bolts.

Twin Series pipe - tube clamps are available along with Multilayer, welding plates, rail nuts, construction types, rubber inley types & many more.

   
   
   
HOSES & HOSE FITTINGS

HOSES & HOSE FITTINGS - AS PER SAE 100 R1/ R2/ R3/ R7/R8/4SH / 4SP HIGH PRESSURE HOSE & S.S. FLEBILE HOSES

OUR HOSES SELECTION CRITERIA ARE AS FOLLOWS:-
SIZE

The inside diameter of the hoses must be adequate to keep pressure loss to a minimum and avoid damage to the hose arising as a result of heat generation or excessive turbulence. Hoses outside diameter can be a critical factor when hoses roufing clamps are used or hoses are routed through bulkhead, check individual hose specification table for O.D.'S.

TEMPERATURE
Both fluid and ambient temperature must be considered while selecting a replacement assembly. The hoses selected must be capable to withstand minimum and maximum temperature of system. While selecting a hoses for its maximum temperature care should taken that temperature stated is not an intermittent value.

APPLICATION
Determine where or how the replacement hose or assembly is le used.

Equipment Type :- Most often only a duplicate of the original hose will have to be made. Make sure all the requirements of the application are fulfilled. While selecting a hoses, its application should be considered i. e. Static / Moving / Flexing.

Working Pressure :- Check individual hose specification table for working pressure. The working pressure or operating pressure is one fourth the hose minimum burst pressure.

Pressure Surges :- In hydraulic systems, where pressure surges are severe, increase the safety factor when selecting the proper hoses (safety factor working / burst = 1/5) Conversaly, in systems where pressure surges are slight or non existent, the normal safety factor must be chosen.

Environmental Conditions :- Care must be taken to ensure that the hoses and fittings are either compatible with or protected from the environment to which they are exposed. Environment conditions including but not limited to ultraviolet heat, ozone, moisture, water, salt water, chemical and air pollutants can cause degradation and premature failure and therefore must be considered.

Mechanical Load :- External forces can significantly reduce hoses life. Mechnical loads which must be considered include excessive flexing, twist, kinking tensile or side loads, bend radius vibration. Use of swivel type fitting or adaptors may be required to ensure no twist is put into the hoses. Unusual applications may require special testing prior to hose selection.

Hose Construction :- Various application may require differnet hoses constructions. For construction please check individual hose specifications.

FLUID TO BE CONVEYED
Hoses selection must assure compatability of the hoses tube, cover, reinforcement and fittings with the fluid use.

PRESSURE
The system pressure should not exceed the mentioned working pressure. Pressure spikes greater than the mentioned working pressure will shorten hoses life. It is not recommended to use hoses on such applications.

Pressure Drop :- When pressurised media is flowing through the hose, there is a certain amount of pressure difference between intake and outlet points, this pressure difference is known a: Pressur Drop. This is due to gradual decrease in the pressure of the media along the length. This aspect shall be considered while designing a hoses.

TYPE OF END FITTINGS
Care must be taken to ensure proper compatability exists between the hoses and the end fittings. Check individual end fitting specification table.

   
1  |  2  |  3  |  4
 
Top
 
 
Single ferrule type | Twin ferrule type | Flare Fittings type | Thread fittings type | Weld Nipple Fittings type | Light series clamps | Heavy series clamps | Twin series clamps | Rubber hoses | Teflon hoses | S.S. flexible hoses | Needle Valves | Ball Valves | Flow Control Valves | Throttle Valves | Check Valves | Quick release couplings | Camlock couplings | Socket weld type | Split type | Butt weld type | Dowety Seals | Copper Washer | Seamless Tubes | 2 way valve manifolds | 3 way valve manifolds | 5 way valve manifolds | Diagnostic Test Coupling
 
 
©2009 Chirag Hydro. All rights reserved.
Web Design & Web Hosting by JupiterIndia.com
Home   |  About Us   |  Products   |  Contact Us